Sunday, August 5, 2018

FTU Want Your Oil Checked


This tut was written August 5th, 2018 for those with a basic knowledge of psp.
I am using the awesome artwork of Keith Garvey
The tube is "Quart Low" 
You need a license to use this tube, do not use without a license.
You can find this tube at his store  HERE
Once his store closes not sure where you will be able to buy his tubes again.

I used PSPX...but any of them should work.
FTU kit Dirty Mechanic by True Taggin Love  HERE
Check out the rest of the blog HERE
RD Mask 754 HERE
Check out the rest of the blog  HERE
Filters
xero-Artworx

Font of choice,  I used Impact and Pacific Again

Drop shadow is usually V-2 H-2 Black, 50, 5, use what you prefer.
Let's get started
*Remember to add your drop shadow as you go along*

Open a new image 800 x 800
Paste paper 8, apply your mask, delete, merge group, apply the mask again,
delete, merge group.

Resize frame 2 to 70%, paste on the right, duplicate, mirror, merge down,
click inside each one with your magic wand, expand by 5, paste paper 1,
invert, delete, change the blend mode to Luminance(L), keep selected.
Paste your middle size tube on one side, then mirror and paste in the other side,
delete, select none, merge down.
Duplicate, go to Adjust, blur, Gaussian blur, number on 4, change the blend mode
to Overlay.  
Apply the xero filter-Artworx, default settings, merge down.

Resize your tube to 85%, paste above the frame about center.

Resize the gear cluster to 75%, paste below the tube to the right, change 
the color by going to Adjust, Hue and Saturation, colorize, both numbers on 0,
duplicate, mirror.

Resize the tire to 70%, paste below the tube to the right a bit.
Resize oil spill 2 to 35%, take your Pick tool, hold the shift key and drag the 
top square down on one side then the other until flat, paste above
the tube at the leg edge, duplicate, move to the left more.
Resize oil spill one to 40%, take the Pick tool and do the same until flat, move
under the gears on the right, duplicate, mirror.

Resize tires to 50%, paste below the tube to the left.
Resize the coupling to 30%, paste at the lower right above the oil spill, duplicate,
move over a little.

Resize the screwdriver to 40%, paste at the lower right on the coupling.
Resize wrench 1 to 30%, paste at the lower left above the oil, free rotate to the 
left at 5 degrees.
Resize wrench 2 to 30%, paste above the first wrench.

Resize the metal barrel to 55%, paste below the tire on the right, duplicate, move
below the gears on the left.
Resize the chain to 35%, paste at the bottom between the oil spills to help
cover the straight edge of the legs, duplicate the chain, move to the 
top of the frame, duplicate, mirror, move both below the tube layer.

Resize the line of washers and nuts to 45%, free rotate to the left at 90 degrees,
paste below the paper layer of the frame at the lower left, duplicate, mirror.

Resize RPM gage to 30%, paste on the right below the coupling.
Resize the headlight to 20%, paste on the left.
Resize grease rag to 25%, paste on the tire below the tube on the right.

Paste the wire fencing below the mask, resize to 95%.

I used Impact for Want Your Oil then Pacific Again.
I resize oil spill 2 to 50%, and place down at the bottom in a couple
of places on each side of the wordart once done.

Add any other elements that you would like, make it your own.

Once happy with your tag, close off any background used, 
crop your tag to make sure no shadows or anything on the edges, merge visible.
Resize your tag first, then add your copyright and name.


That's it
Hope you enjoyed doing my tut.


No comments:

Post a Comment