FTU Lucky Day 3 Piece Set

This tut was written March 10th, 2020 for those with a basic knowledge of psp.

I am using the awesome artwork of Alex Prihodko

The tube is called "Lucky Day 2"

You need a license to use this tube, do not use without a license.

You can find this tube at VMArtists  store  HERE

I used PSPX...but any of them should work.

FTU kit St Patty's Luck by Scrap Dimensions  HERE
Check out the rest of the blog HERE

Mask of choice, I used RD Mask 749  HERE
Check out the rest of the blog HERE

Font of choice,  I used Paulistana

Drop shadow is usually V-2 H-2 Black, 50, 5, use what you prefer.

Let's get started

*Remember to add your drop shadow as you go along*

Open a new image 800 x 800
Paste paper 2, apply your mask, delete, merge group.

Resize element 34 to 85%, free rotate to the right at 15 degrees,
paste, go to Effects, 3D Effects, Inner bevel
with these settings.
Bevel shape 2, width 25
10, 3, 5, 24
174, 50, 30 
Color in white
Select all, float, defloat, add a new layer, expand by 3, fill with a 
dark color from your tube, move below the frame, select none.

Click inside the frame, expand by 5, paste paper 2, invert, delete,
keep selected, paste your tube on the upper left in the frame so the rabbit 
shows, delete.
Mirror your tube, paste on the right in the frame, delete, select none,
merge down.
Duplicate, go to Adjust, Blur, Gaussian blur, number on 4, change
the blend mode to Overlay or one you prefer.

Resize your tube to 45%, paste above the tube about center.
Paste element 45 below the tube.

Resize element 8 and 9 to 30%, paste 8 first, apply the same bevel settings
as before, paste on the frame at the top behind the tube.
Apply the bevel setting to 9,  paste on top of the first bow.

Paste element 28 on the left below the tube, add the same bevel settings,
duplicate, mirror, move below the paper layer on the right just do 
the grass shows.

Resize element 25 to 80%, flip, free rotate to the right at 15 degrees, paste below 
the paper layer of the frame at the top, duplicate, free rotate to the right 
at 90 degrees, adjust on the right, erase the parts past the frame,
duplicate, mirror, flip, adjust on the left, erase any part that needs it.
Apply the inner bevel to these also.

Resize element 23 to 35%, paste at the bottom right below the tube.
Resize element 1 to 35%, paste at the lower right below the elf.
Resize element 7 to 35%, paste at the lower left above the tube.

Resize element 2 to 35%, paste behind the elf.
Resize element 3 to 15%, paste above the tube by the elf.
Resize element 17 to 20%, paste on the pot of gold.
Resize element 38 to 90%, paste below the tube on the pot of gold.

Go back to the pot of gold duplicate, resize to 85%, take your free 
hand tool, draw around the gold at the bottom, copy, paste as a new 
layer, then paste it under the tube, duplicate, move over more how you like.
Resize element 19 to 40%, paste on the frame on the left behind the pot
of gold, duplicate, mirror.

Signature tag 
600 x 200 
Close off your tube, paste tag.
Go back and open your tube, copy and paste where you like,
merge visible, add frame of choice.
Ava 
150 x 180 or size of choice, copy the tag and resize smaller and 
place how you like, merge, frame of choice.

Add any other elements that you would like, make it your own.

Always readjust your mask and elements how you like them before you

 merge your tag, sharpen once.

Crop your tag to make sure no shadows or anything on the edges, merge visible.

 Then add your copyright and name.

That's it

Hope you enjoyed doing my tut.